- DATA ITEM DESCRIPTION
- 1. TITLE
- 2. IDENTIFICATION NUMBER
- 3. DESCRIPTION/PURPOSE
- 4. APPROVAL DATE
- 5. OFFICE OF PRIMARY RESPONSIBILITY
- 7. APPLICATION/INTERRELATIONSHIP
- 10. PREPARATION INSTRUCTIONS
- 10.1 Content and format instructions.
- 10.1.1 Title page.
- 10.1.2 Table of contents.
- 10.1.3 Scope.
- 10.1.3.1 Identification.
- 10.1.3.2 System overview.
- 10.1.3.3 Document overview.
- 10.1.4 Referenced documents.
- 10.1.5 Computer system operation.
- 10.1.5.1 Computer system preparation and shutdown.
- 10.1.5.1.1 Power on and off.
- 10.1.5.2 Initiation.
- 10.1.5.1.3 Shutdown.
- 10.1.5.2 Operating procedures.
- 10.1.5.1 Input and output procedures.
- 10.1.5.2.2 Monitoring procedures.
- 10.1.5.2.3 Recovery procedures.
- 10.1.5.2.4 Off-line routine procedures.
- 10.1.5.2.5 Other procedures.
- 10.1.6 Diagnostic features.
- 10.1.6.1 Diagnostic features summary.
- 10.1.6.2 Diagnostic procedures.
- 10.1.6.2.1 (Procedure name).
- 10.1.6.3 Diagnostic tools.
- 10.1.6.3.1 (Diagnostic tool name).
- 10.1.7 Notes.
- 10.1.8 Appendixes.
- 11. DISTRIBUTION STATEMENT
Form Approved OMB No. 0704-0188
The following establishes the data general and content requirements for the identified data item.
Computer System Operator's Manual (CSOM)
The Computer System Operator's Manual (CSOM) provides information and detailed procedures for initiating, operating, monitoring, and shutting down a computer system and for identifying/isolating a malfunctioning component in a computer system.
A CSOM is developed for each computer system in which one or more CSCIs execute.
6a. DTIC APPLICABLE
6b. GIDEP APPLICABLE
This Data Item Description (DID) contains the format and content preparation instructions for data generated under the task described by paragraph 4.6.4 of DOD-STD-2167A.
The Contract Data Requirements List should specify whether this document is to be prepared and delivered on bound 8 1/2 by 11 inch bond paper or electronic media. If electronic media is selected, the precise format must be specified.
This DID supersedes DI-MCCR-80018 and DI-MCCR-80020 dated 4 June 1985.
9a. APPLICABLE FORMS
9b. AMSC NUMBER
Production of this manual using automated techniques is encouraged. Specific content and format instructions for this manual are identified below.
- a. Response to tailoring instructions.
In the event that a paragraph or subparagraph has been tailored out, a statement to that effect shall be added directly following heading of each such (sub)paragraph. If a paragraph and all of its subparagraphs are tailored out, only the highest level paragraph heading need be included.
- b. Use of alternate presentation styles.
Charts, tables, matrices, or other presentation styles are acceptable when the information required by the paragraphs and subparagraphs of this DID can de made more readable.
- c. Page numbering.
Each page prior to Section 1 shall be numbered in lower-case roman numerals beginning with page ii for the Table of Contents. Each page starting from Section 1 to the beginning of the appendixes shall be consecutively numbered in arabic numerals. If the document is into volumes, each such volume shall restart the numbering sequence.
- d. Document control numbers.
For hardcopy formats, this document may be printed on one or both sides of each page (single-sided/double-sided). All printed pages shall contain the document control number and the date of the document centered at the top of the page. Document control numbers shall include revision and volume identification as applicable.
- e. Multiple (sub)paragraphs.
All paragraphs and subparagraphs starting with the phrase "This (sub)paragraph shall..." may be written as multiple subparagraphs to enhance readability. These subparagraphs shall be numbered sequentially.
- f. Identifiers.
The letter "X" serves as an identifier for a series of descriptions. For example, the subparagraphs of paragraph 10.1.6.2 describes diagnostic procedures and is presented in the following structure:
4.2 Diagnostic procedures. 4.2.1 (Name of the e first diagnostic procedure). 4.2.2 (Name of the second diagnostic procedure). 4.2.3 etc.
- g. Document structure.
This manual shall consist of the following:
(1) Cover (2) Title page (3) Table of contents (4) Scope (5) Referenced documents (6) Computer system operation (7) Diagnostic features (8) Notes (9) Appendixes.
The title page shall contain the information specified below in the indicated format:
[Document control number and data: Volume x of y (if multi-volume)] [Rev. indicator: date of Rev.] COMPUTER SYSTEM OPERATOR'S MANUAL FOR THE [COMPUTER SYSTEM NAME] OF [SYSTEM NAME] CONTRACT NO. [contract number] CDRL SEQUENCE NO. [RDRL number] Prepared for. [Contracting agency Name, department code] Prepared by. [contractor name and address]
This manual shall contain a table of contents listing the title and page number of each titled paragraph and subparagraph. The table of contents shall then list the title and page number of each figure, table, and appendix, in that order.
This section shall be numbered 1 and shall be divided into the following paragraphs.
This paragraph shall be numbered 1.1 and shall contain the approved identification number, title, and abbreviation, if applicable, of the computer system to which this CSOM applies.
This paragraph shall be numbered 1.2 and shall briefly state the purpose of the system and the software to which this CSOM applies.
This paragraph shall be numbered 1.3 and shall summarize the purpose and contents of this manual.
This section shall be numbered 2 and shall list by document number and title all documents referenced in this manual. This section shall also identify the source for all documents not available through normal Government stocking activities.
This section shall be numbered 3 and shall be divided into the following paragraphs and subparagraphs to describe the instructions for operation of the computer system. This section may reference commercially available documents for the information required by the following paragraphs and subparagraphs.
This paragraphs shall be numbered 3.1 and shall be divided into the following subparagraphs to described the procedures for computer system preparation and setup prior to computer system operation.
This subparagraph shall be numbered 3.1.1 and shall explain the step-by-step procedures required to power-on and power-off the computer system.
This subparagraph shall be numbered 3.1.2 and shall contain the initiation procedures necessary to operate the computer system. This subparagraph shall described the following:
The equipment setup and the procedures required for pre-operation.
The procedures necessary to bootstrap the computer system and to load software and data.
The commands typically used during computer system initiation.
The procedures necessary to initialize files, variables, or other parameters.
This subparagraph shall be numbered 3.1.3 and shall contain the shutdown procedures necessary to save data files and other information and to terminate computer system operation.
This paragraph shall be numbered 3.2 and shall be divided into the following subparagraphs to contain the procedures necessary to operate the computer system once the initiation procedures are complete. If more than one mode of operation is available, instructions for each mode shall be provided.
This subparagraph shall be numbered 3.2.1, shall describe the input and output media (e.g., magnetic tape, disk, cartridge, etc.) relevant to the computer system and shall explain the procedures required to read and write on these media. This subparagraph shall briefly describe the operating system control language and shall also list operator procedures for interactive messages and replies (e.g., which terminal to use, password use, log on and log off procedures).
This subparagraph shall be numbered 3.2.2 and shall contain the procedures to be followed for monitoring the software in operation. Applicable trouble and malfunction indications shall be included. Evaluation techniques for fault isolation shall be described to the maximum extent practical. This subparagraph shall also include descriptions of conditions requiring computer system shutdown. Procedures for on-line intervention, abort, and user communications shall also be included.
This subparagraph shall be numbered 3.2.3 and shall describe the automatic and manual procedures to be followed for each trouble occurrence (e.g., have detailed instructions to obtain computer system dumps). This subparagraph shall describe the steps to be taken by the operator to restart computer system operation after an abort or interruption of operation. Procedures for recording information concerning a malfunction shall also be included.
This subparagraph shall be numbered 3.2.4 and shall contain the procedures required to operate all relevant off-line routines of the computer system.
This subparagraph shall be numbered 3.2.5 and shall contain any additional procedures to be followed by the operator (e.g., computer system alarms, program or computer system security considerations, switch over to a redundant computer system).
This section shall be numbered 4 and shall be divided into the following paragraphs and subparagraphs to describe the diagnostic features available to the computer operator. This section may reference commercially available documents for the information required by the following paragraphs and subparagraphs.
This paragraph shall be numbered 4.1 and shall summarize the error-detection and diagnostic features available in the computer system, including error message syntax and hierarchy for fault isolation. This paragraph shall describe the purpose of each diagnostic feature.
This paragraph shall be numbered 4.2 and shall be divided into t he following subparagraphs to identify and describe the diagnostic procedures.
This subparagraph shall be numbered 4.2X (beginning with 4.2.1), shall identify a diagnostic procedure, and shall describe its purpose. Reference may be made to section 3 of this document, as appropriate, for computer system operating instructions that support the diagnostic procedure. This subparagraph shall describe:
Hardware, software, or firmware necessary for executing the procedure
Step-by-step instructions for execution the procedure
Diagnostic messages and the corresponding required action.
This paragraph shall be numbered 4.3 and shall be divided into the following subparagraphs to describe each diagnostic tool available to the computer operator. A diagnostic tool may contain hardware, software, firmware, or a combination of these and provides diagnostic capabilities.
This subparagraph shall be numbered 4.3.X (beginning with 4.3.1), shall identify a diagnostic tool by name and shall describe the tool and its application.
This section shall be numbered 6 and shall contain any general information that aids in understanding this document (e.g., background information, glossary). This section shall include an alphabetical listing of all acronyms, abbreviations, and their meanings as used in this document.
Appendixes may be used to provide information published separately for convenience in document maintenance (e.g., charts, classified data). As applicable, each appendix shall be referenced in the main body of the document where the data would normally have been provided. Appendixes may be bound as separate documents for ease in handling. Appendixes shall be lettered alphabetically (A,B, etc.), and the paragraphs within each appendix be numbered as multiples of 10 (e.g., Appendix A, paragraph 10, 10.1, 10.2, 20, 20.1, 20.2, etc.). Pages within each appendix shall be numbered alpha-numerically as follows: Appendix A pages shall be numbered A-1, A-2, A-3, etc. Appendix B pages shall be numbered B-1, B-2, B-3, etc.
Approved for public release; distribution in unlimited.
DD Form 1664, JUN 86 Previous editions are obsolete