Tinkerforge::BrickletOutdoorWeather - 433MHz receiver for outdoor weather station
This constant is used to identify a Outdoor Weather Bricklet.
The get_identity() subroutine and the CALLBACK_ENUMERATE callback of the IP Connection have a device_identifier parameter to specify the Brick's or Bricklet's type.
This constant represents the display name of a Outdoor Weather Bricklet.
This constant is used with the register_callback() subroutine to specify the CALLBACK_STATION_DATA callback.
This constant is used with the register_callback() subroutine to specify the CALLBACK_SENSOR_DATA callback.
This constant is used with the get_response_expected(), set_response_expected() and set_response_expected_all() subroutines.
Creates an object with the unique device ID *uid* and adds it to the IP Connection *ipcon*.
Returns the identifiers (number between 0 and 255) of all `stations <https://www.tinkerforge.com/en/shop/accessories/sensors/outdoor-weather-station-ws-6147.html>`__ that have been seen since the startup of the Bricklet.
Each station gives itself a random identifier on first startup.
Since firmware version 2.0.2 a station is removed from the list if no data was received for 12 hours.
Returns the identifiers (number between 0 and 255) of all `sensors <https://www.tinkerforge.com/en/shop/accessories/sensors/temperature-humidity-sensor-th-6148.html>`__ that have been seen since the startup of the Bricklet.
Each sensor gives itself a random identifier on first startup.
Since firmware version 2.0.2 a sensor is removed from the list if no data was received for 12 hours.
Returns the last received data for a station with the given identifier. Call :func:`Get Station Identifiers` for a list of all available identifiers.
The return values are:
* Temperature in °C/10, * Humidity in %RH, * Wind Speed in m/10s, * Gust Speed in m/10s, * Rain Fall in mm/10, * Wind Direction (N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW), * Battery Low (true or false) and * Last Change (time in seconds since the reception of this data).
Returns the last measured data for a sensor with the given identifier. Call :func:`Get Sensor Identifiers` for a list of all available identifiers.
* Temperature in °C/10, * Humidity in %RH and * Last Change (time in seconds since the last reception of data).
Turns callback for station data on or off. Default is off.
Returns the configuration as set by :func:`Set Station Callback Configuration`.
Turns callback for sensor data on or off. Default is off.
Returns the configuration as set by :func:`Set Sensor Callback Configuration`.
Returns the error count for the communication between Brick and Bricklet.
The errors are divided into
* ACK checksum errors, * message checksum errors, * framing errors and * overflow errors.
The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.
Sets the bootloader mode and returns the status after the requested mode change was instigated.
You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.
This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.
Returns the current bootloader mode, see :func:`Set Bootloader Mode`.
Sets the firmware pointer for :func:`Write Firmware`. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).
Writes 64 Bytes of firmware at the position as written by :func:`Set Write Firmware Pointer` before. The firmware is written to flash every 4 chunks.
You can only write firmware in bootloader mode.
Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.
You can also turn the LED permanently on/off or show a heartbeat.
If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.
Returns the configuration as set by :func:`Set Status LED Config`
Returns the temperature in °C as measured inside the microcontroller. The value returned is not the ambient temperature!
The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.
Calling this function will reset the Bricklet. All configurations will be lost.
After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!
Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.
We recommend that you use Brick Viewer to change the UID.
Returns the current UID as an integer. Encode as Base58 to get the usual string version.
Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.
The position can be 'a', 'b', 'c' or 'd'.
The device identifier numbers can be found :ref:`here <device_identifier>`. |device_identifier_constant|
To install Tinkerforge, copy and paste the appropriate command in to your terminal.
cpanm
cpanm Tinkerforge
CPAN shell
perl -MCPAN -e shell install Tinkerforge
For more information on module installation, please visit the detailed CPAN module installation guide.