NAME

Device::Chip::MAX11200 - chip driver for MAX11200

SYNOPSIS

 use Device::Chip::MAX11200;

 my $chip = Device::Chip::MAX11200->new;
 $chip->mound( Device::Chip::Adapter::...->new )->get;

 $chip->trigger->get;

 printf "The reading is %d\n", $chip->read_adc->get;

DESCRIPTION

This Device::Chip subclass provides specific communications to a Maxim MAX11200 or MAX11210 chip.

The reader is presumed to be familiar with the general operation of this chip; the documentation here will not attempt to explain or define chip-specific concepts or features, only the use of this module to access them.

METHODS

The following methods documented with a trailing call to ->get return Future instances.

read_status

   $status = $chip->read_status->get

Returns a HASH reference containing the chip's current status.

   RDY   => 0 | 1
   MSTAT => 0 | 1
   UR    => 0 | 1
   OR    => 0 | 1
   RATE  => 1 | 2.5 | 5 | 10 | 15 | 30 | 60 | 120
   SYSOR => 0 | 1

read_config

   $config = $chip->read_config->get

Returns a HASH reference containing the chip's current configuration.

   SCYCLE => 0 | 1
   FORMAT => "TWOS_COMP" | "OFFSET"
   SIGBUF => 0 | 1
   REFBUF => 0 | 1
   EXTCLK => 0 | 1
   UB     => "UNIPOLAR" | "BIPOLAR"
   LINEF  => "60Hz" | "50Hz"
   NOSCO  => 0 | 1
   NOSCG  => 0 | 1
   NOSYSO => 0 | 1
   NOSYSG => 0 | 1
   DGAIN  => 1 2 4 8 16  # only valid for the MAX11210

change_config

   $chip->change_config( %changes )->get

Changes the configuration. Any field names not mentioned will be preserved at their existing values.

selfcal

   $chip->selfcal->get

Requests the chip perform a self-calibration.

syscal_offset

   $chip->syscal_offset->get

Requests the chip perform the offset part of system calibration.

syscal_gain

   $chip->syscal_gain->get

Requests the chip perform the gain part of system calibration.

trigger

   $chip->trigger( $rate )->get

Requests the chip perform a conversion of the input level, at the given rate (which must be one of the values specified for the RATE configuration option); defaulting to 120 if not defined. Once the conversion is complete it can be read using the read_adc method.

read_adc

   $value = $chip->read_adc->get

Reads the most recent reading from the result register on the tip. This method should be called after a suitable delay after the "trigger" method when in single cycle mode, or at any time when in continuous mode.

The reading is returned directly from the chip as a plain 24-bit integer, either signed or unsigned as per the FORMAT configuration.

write_gpios

   $chip->write_gpios( $values, $direction )->get

read_gpios

   $values = $chip->read_gpios->get

Sets or reads the values of the GPIO pins as a 4-bit integer. Bits in the $direction should be high to put the corresponding pin into output mode, or low to put it into input mode.

Calibration Registers

   $value = $chip->read_selfcal_offset->get;
   $value = $chip->read_selfcal_gain->get;
   $value = $chip->read_syscal_offset->get;
   $value = $chip->read_syscal_gain->get;

   $chip->write_selfcal_offset( $value )->get;
   $chip->write_selfcal_gain( $value )->get;
   $chip->write_syscal_offset( $value )->get;
   $chip->write_syscal_gain( $value )->get;

Reads or writes the values of the calibration registers, as plain 24-bit integers.

AUTHOR

Paul Evans <leonerd@leonerd.org.uk>

cpanm Device::Chip::AnalogConverters

perl -MCPAN -e shell
install Device::Chip::AnalogConverters