- DATA ITEM DESCRIPTION
- 1. TITLE
- 2. IDENTIFICATION NUMBER
- 3. DESCRIPTION/PURPOSE
- 7. APPLICATION/INTERRELATIONSHIP
- 10. PREPARATION INSTRUCTIONS
- 10.1 General instructions.
- 10.1.1 Automated techniques
- 10.1.2 Alternate presentation styles
- 10.1.3 Title page or identifier with signature blocks.
- 10.1.4 Table of contents.
- 10.1.5 Page numbering/labeling.
- 10.1.6 Response to tailoring instructions.
- 10.1.7 Multiple paragraphs and subparagraphs.
- 10.1.8 Standard data descriptions.
- 10.1.9 Substitution of existing documents.
- 10.2 Content requirements.
- 1. Scope.
- 2. Referenced documents.
- 3. Computer system operation.
- 4. Diagnostic features.
- 5. Notes.
- A. Appendixes.
- Copyright Holder Contact
The following establishes the data general and content requirements for the identified data item.
COMPUTER OPERATION MANUAL (COM)
The Computer Operation Manual (COM) provides information needed to operate a given computer and its peripheral equipment. This manual focuses on the computer itself, not on particular software that will run on the computer.
The COM is intended for newly developed computers, special-purpose computers, or other computers for which commercial or other operation manuals are not readily available.
This Data Item Description (DID) contains the format and content preparation instructions for the data product generated by specific and discrete task requirements as delineated in the contract.
This DID is used when the developer is tasked to identify and record information needed to operate the computer(s) on which software will run.
The Contract Data Requirements List (CDRL) should specify whether deliverable data are to be delivered on paper or electronic media; are to be in a given electronic form (such as ASCII, CALS, or compatible with a specified word processor or other support software); may be delivered in developer format rather than in the format specified herein; and may reside in a computer-aided software engineering (CASE) or other automated tool rather than in the form of a traditional document.
This DID supersedes DI-MCCR-80018A and DI-MCCR-80316.
Use of automated techniques is encouraged. The term 'document' in this DID means a collection of data regardless of its medium.
Diagrams, tables, matrices, and other presentation styles are acceptable substitutes for text when data required by this DID can be made more readable using these styles.
The document shall include a title page containing, as applicable: document number; volume number; version/revision indicator; security markings or other restrictions on the handling of the document; date; document title; name, abbreviation, and any other identifier for the systems, subsystems, or items to which the document applies; contract number; CDRL item number; organization for which the document has been prepared; name and address of the preparing organization; distribution statement; and signature blocks for the developer representative authorized to release the document, the acquirer representative authorized to approve the document, and the dates of release/approval. For data in a database or other alternative form, this information shall be included on external and internal labels or by equivalent identification methods.
The document shall contain a table of contents providing the number, title, and page number of each titled paragraph, figure, table, and appendix. For data in a database or other alternative form, this information shall consist of an internal or external table of contents containing pointers to, or instructions for accessing, each paragraph, figure, table, and appendix or their equivalents.
Each page shall contain a unique page number and display the document number, including version, volume, and date, as applicable. For data in a database or other alternative form, files, screens, or other entities shall be assigned names or numbers in such a way that desired data can be indexed and accessed.
If a paragraph is tailored out of this DID, the resulting document shall contain the corresponding paragraph number and title, followed by 'This paragraph has been tailored out.' For data in a database or other alternative form, this representation need occur only in the table of contents or equivalent.
Any section, paragraph, or subparagraph in this DID may be written as multiple paragraphs or subparagraphs to enhance readability.
If a data description required by this DID has been published in a standard data element dictionary specified in the contract, reference to an entry in that dictionary is preferred over including the description itself.
Commercial or other existing documents may be substituted for all or part of the document if they contain the required data.
Content requirements begin on the following page. The numbers shown designate the paragraph numbers to be used in the document. Each such number is understood to have the prefix '10.2' within this DID. For example, the paragraph numbered 1.1 is understood to be paragraph 10.2.1.1 within this DID.
This section shall be divided into the following paragraphs.
This paragraph shall contain the manufacturer's name, model number, and any other identifying information for the computer system to which this COM applies.
This paragraph shall briefly state the purpose of the computer system to which this COM applies.
This paragraph shall summarize the purpose and contents of this manual and shall describe any security or privacy considerations associated with its use.
This section shall list the number, title, revision, and date of all documents referenced in this manual. This section shall also identify the source for all documents.
This section shall be divided into the following paragraphs. Safety precautions, marked by WARNING or CAUTION, shall be included where applicable.
This paragraph shall be divided into the following subparagraphs.
This paragraph shall contain the procedures necessary to power-on and power-off the computer system.
This paragraph shall contain the procedures necessary to initiate operation of the computer system, including, as applicable, equipment setup, pre-operation, bootstrapping, and commands typically used during computer system initiation.
This paragraph shall contain the procedures necessary to terminate computer system operation.
This paragraph shall be divided into the following subparagraphs. If more than one mode of operation is available, instructions for each mode shall be provided.
This paragraph shall describe the input and output media (e.g., magnetic disk, tape) relevant to the computer system, state the procedures to read and write on these media, briefly describe the operating system control language, and list procedures for interactive messages and replies (e.g., terminals to use, passwords, keys).
This paragraph shall contain the procedures to be followed for monitoring the computer system in operation. It shall describe available indicators, interpretation of those indicators, and routine and special monitoring procedures to be followed.
This paragraph shall contain the procedures necessary to operate all relevant off-line equipment of the computer system.
This paragraph shall contain any additional procedures to be followed by the operator (e.g., computer system alarms, computer system security or privacy considerations, switch over to a redundant computer system, or other measures to ensure continuity of operations in the event of emergencies).
This paragraph shall identify problems that may occur in any step of operation described in the preceding paragraphs in Section 3. It shall state the error messages or other indications accompanying those problems and shall describe the automatic and manual procedures to be followed for each occurrence, including, as applicable, evaluation techniques, conditions requiring computer system shutdown, procedures for on-line intervention or abort, steps to be taken to restart computer system operation after an abort or interruption of operation, and procedures for recording information concerning a malfunction.
This section shall be divided into the following paragraphs to describe diagnostics that may be performed to identify and troubleshoot malfunctions in the computer system.
This paragraph shall summarize the diagnostic features of the computer system, including error message syntax and hierarchy for fault isolation. This paragraph shall describe the purpose of each diagnostic feature.
This paragraph shall be divided into subparagraphs as needed to describe the diagnostic procedures to be followed for the computer system, including:
Identification of hardware, software, or firmware necessary for executing each procedure
Step-by-step instructions for executing each procedure
Diagnostic messages and the corresponding required action
This paragraph shall be divided into subparagraphs as needed to describe the diagnostics tools available for the computer system. These tools may be hardware, software, or firmware. This paragraph shall identify each tool by name and number and shall describe the tool and its application.
This section shall contain any general information that aids in understanding this document (e.g., background information, glossary, rationale). This section shall include an alphabetical listing of all acronyms, abbreviations, and their meanings as used in this document and a list of terms and definitions needed to understand this document.
Appendixes may be used to provide information published separately for convenience in document maintenance (e.g., charts, classified data). As applicable, each appendix shall be referenced in the main body of the document where the data would normally have been provided. Appendixes may be bound as separate documents for ease in handling. Appendixes shall be lettered alphabetically (A, B, etc.).
This Perl Plain Old Documentation (POD) version is copyright © 2001 2003 Software Diamonds. This POD version was derived from the hard copy public domain version freely distributed by the United States Federal Government.
Software Diamonds permits the redistribution and use in source and binary forms, with or without modification, provided that the following conditions are met:
Redistributions of source code, modified or unmodified
must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
SOFTWARE DIAMONDS, http://www.SoftwareDiamonds.com, PROVIDES THIS SOFTWARE 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL SOFTWARE DIAMONDS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING USE OF THIS SOFTWARE, EVEN IF ADVISED OF NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE POSSIBILITY OF SUCH DAMAGE.
1 POD Error
The following errors were encountered while parsing the POD:
- Around line 325:
Non-ASCII character seen before =encoding in '©'. Assuming ISO8859-1