Tinkerforge::BrickletMultiTouchV2 - Capacitive touch sensor for 12 electrodes
This constant is used to identify a Multi Touch Bricklet 2.0.
The get_identity() subroutine and the CALLBACK_ENUMERATE callback of the IP Connection have a device_identifier parameter to specify the Brick's or Bricklet's type.
This constant represents the display name of a Multi Touch Bricklet 2.0.
This constant is used with the register_callback() subroutine to specify the CALLBACK_TOUCH_STATE callback.
This constant is used with the get_response_expected(), set_response_expected() and set_response_expected_all() subroutines.
Creates an object with the unique device ID *uid* and adds it to the IP Connection *ipcon*.
Returns the current touch state. The state is given as a array of bools.
Element 0 to 11 represent the 12 electrodes and element 12 represents the proximity.
If an electrode is touched, the corresponding element is *true*. If a hand or similar is in proximity to the electrodes, element 12 is *true*.
The proximity is activated with a distance of 1-2cm. An electrode is already counted as touched if a finger is nearly touching the electrode. This means that you can put a piece of paper or foil or similar on top of a electrode to build a touch panel with a professional look.
If you want to get the value periodically, it is recommended to use the :cb:`Touch State` callback. You can set the callback configuration with :func:`Set Touch State Callback Configuration`.
The period is the period with which the :cb:`Touch State` callback is triggered periodically. A value of 0 turns the callback off.
If the `value has to change`-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.
If it is set to false, the callback is continuously triggered with the period, independent of the value.
Returns the callback configuration as set by :func:`Set Touch State Callback Configuration`.
Recalibrates the electrodes. Call this function whenever you changed or moved you electrodes.
Enables/disables electrodes with a bool array (see :func:`Get Touch State`).
*True* enables the electrode, *false* disables the electrode. A disabled electrode will always return *false* as its state. If you don't need all electrodes you can disable the electrodes that are not needed.
It is recommended that you disable the proximity electrode (element 12) if the proximity feature is not needed. This will reduce the amount of traffic that is produced by the :cb:`Touch State` callback.
Disabling electrodes will also reduce power consumption.
Returns the electrode configuration, as set by :func:`Set Electrode Config`.
Sets the sensitivity of the electrodes. An electrode with a high sensitivity will register a touch earlier then an electrode with a low sensitivity.
If you build a big electrode you might need to decrease the sensitivity, since the area that can be charged will get bigger. If you want to be able to activate an electrode from further away you need to increase the sensitivity.
After a new sensitivity is set, you likely want to call :func:`Recalibrate` to calibrate the electrodes with the newly defined sensitivity.
Returns the current sensitivity, as set by :func:`Set Electrode Sensitivity`.
Configures the touch LED to be either turned off, turned on, blink in heartbeat mode or show the touch state (electrode touched = LED on).
Returns the LED configuration as set by :func:`Set Touch LED Config`
Returns the error count for the communication between Brick and Bricklet.
The errors are divided into
* ACK checksum errors, * message checksum errors, * framing errors and * overflow errors.
The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.
Sets the bootloader mode and returns the status after the requested mode change was instigated.
You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.
This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.
Returns the current bootloader mode, see :func:`Set Bootloader Mode`.
Sets the firmware pointer for :func:`Write Firmware`. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).
Writes 64 Bytes of firmware at the position as written by :func:`Set Write Firmware Pointer` before. The firmware is written to flash every 4 chunks.
You can only write firmware in bootloader mode.
Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.
You can also turn the LED permanently on/off or show a heartbeat.
If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.
Returns the configuration as set by :func:`Set Status LED Config`
Returns the temperature as measured inside the microcontroller. The value returned is not the ambient temperature!
The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.
Calling this function will reset the Bricklet. All configurations will be lost.
After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!
Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.
We recommend that you use Brick Viewer to change the UID.
Returns the current UID as an integer. Encode as Base58 to get the usual string version.
Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.
The position can be 'a', 'b', 'c', 'd', 'e', 'f', 'g' or 'h' (Bricklet Port). A Bricklet connected to an :ref:`Isolator Bricklet <isolator_bricklet>` is always at position 'z'.
The device identifier numbers can be found :ref:`here <device_identifier>`. |device_identifier_constant|
To install Tinkerforge, copy and paste the appropriate command in to your terminal.
cpanm
cpanm Tinkerforge
CPAN shell
perl -MCPAN -e shell install Tinkerforge
For more information on module installation, please visit the detailed CPAN module installation guide.