NAME

Plack::Middleware::Greylist - throttle requests with different rates based on net blocks

VERSION

version v0.3.2

SYNOPSIS

  use Plack::Builder;

  builder {

    enable "Greylist",
      file         => sprintf('/run/user/%u/greylist', $>), # cache file
      default_rate => 250,
      greylist     => {
          '192.168.0.0/24' => 'whitelist',
          '172.16.1.0/25'  => [ 100, 'netblock' ],
      };

  }

DESCRIPTION

This middleware will apply rate limiting to requests, depending on the requestor netblock.

Hosts that exceed their configured per-minute request limit will be rejected with HTTP 429 errors.

Log Messages

Rejections will be logged with a message of the form

    Rate limiting $ip after $hits/$rate for $netblock

for example,

    Rate limiting 172.16.0.10 after 225/250 for 172.16.0.0/24

Note that the $netblock for the default rate is simply "default", e.g.

    Rate limiting 192.168.0.12 after 101/100 for default

This will allow you to use something like fail2ban to block repeat offenders, since bad robots are like houseflies that repeatedly bump against closed windows.

ATTRIBUTES

default_rate

This is the default maximum number of hits per minute before requests are rejected, for any request not in the "greylist".

Omitting it will disable the global rate.

retry_after

This sets the Retry-After header value, in seconds. It defaults to 61 seconds, which is the minimum allowed value.

Note that this does not enforce that a client has waited that amount of time before making a new request, as long as the number of hits per minute is within the allowed rate.

greylist

This is a hash reference to the greylist configuration.

The keys are network blocks, and the values are an array reference of rates and the tracking type. (A string of space- separated values can be used instead, to make it easier to directly use the configuration from something like Config::General.)

The rates are either the maximum number of requests per minute, or "whitelist" to not limit the network block, or "blacklist" to always forbid a network block.

(The rate "-1" corresponds to "whitelist", and the rate "0" corresponds to "blacklist".)

The tracking type defaults to "ip", which applies limits to individual ips. You can also use "netblock" to apply the limits to all hosts in that network block, or use a name so that limits are applied to all hosts in network blocks with that name.

For example:

    {
        '127.0.0.1/32' => 'whitelist',

        '192.168.1.0/24' => 'blacklist',

        '192.168.2.0/24' => [ 100, 'ip' ],

        '192.168.3.0/24' => [  60, 'netblock' ],

        # All requests from these blocks will limited collectively

        '10.0.0.0/16'    => [  60, 'group1' ],
        '172.16.0.0/16'  => [  60, 'group1' ],
    }

Note: the network blocks shown above are examples only.

The limit may be larger than "default_rate", to allow hosts to exceed the default limit.

file

This is the path of the throttle count file used by the "cache".

It is required unless you are defining your own "cache".

cache

This is a code reference to a function that increments the cache counter for a key (usually the IP address or net block).

If you customise this, then you need to ensure that the counter resets or expires counts after a set period of time, e.g. one minute. If you use a different time interval, then you may need to adjust the "retry_after" time.

KNOWN ISSUES

This does not try and enforce any consistency or block overlapping netblocks. It trusts Net::IP::Match::Trie to handle any overlapping or conflicting network ranges, or to specify exceptions for larger blocks.

Some search engine robots may not respect HTTP 429 responses, and will treat these as errors. You may want to make an exception for trusted networks that gives them a higher rate than the default.

SOURCE

The development version is on github at https://github.com/robrwo/Plack-Middleware-Greylist- and may be cloned from git://github.com/robrwo/Plack-Middleware-Greylist-.git

BUGS

Please report any bugs or feature requests on the bugtracker website https://github.com/robrwo/Plack-Middleware-Greylist-/issues

When submitting a bug or request, please include a test-file or a patch to an existing test-file that illustrates the bug or desired feature.

AUTHOR

Robert Rothenberg <rrwo@cpan.org>

The initial development of this module was sponsored by Science Photo Library https://www.sciencephoto.com.

COPYRIGHT AND LICENSE

This software is Copyright (c) 2022 by Robert Rothenberg.

This is free software, licensed under:

  The Artistic License 2.0 (GPL Compatible)

cpanm Plack::Middleware::Greylist

perl -MCPAN -e shell
install Plack::Middleware::Greylist