Panotools::Script::Line::Image - Panotools input image


A single input image is described by an 'i' line


Basically the same format as an 'o' line.

  h500     nona requires the width and height of input images wheras PTStitcher/mender don't

  f0           projection format,
                   0 - rectilinear (normal lenses)
                   1 - Panoramic (Scanning cameras like Noblex)
                   2 - Circular fisheye
                   3 - full-frame fisheye
                   4 - PSphere, equirectangular
                   7 - Mirror (a spherical mirror)
                   8 - Orthographic fisheye
                  10 - Stereographic fisheye
                  21 - Equisolid fisheye

  v82          horizontal field of view of image (required)
  y0           yaw angle (required)
  p43          pitch angle (required)
  r0           roll angle (required)
  a,b,c        lens correction coefficients (optional)
  d,e          initial lens offset in pixels(defaults d0 e0, optional).
                   Used to correct for offset from center of image
                   d - horizontal offset,
                   e - vertical offset
  g,t          initial lens shear.  Use to remove slight misalignment
                   of the line scanner relative to the film transport
                   g - horizontal shear
                   t - vertical shear
  j            stack number

  Eev          exposure of image in EV (exposure values)
  Er           white balance factor for red channel
  Eb           white balance factor for blue channel

  Ra           EMoR response model from the Computer Vision Lab at Columbia University
  Rb           This models the camera response curve

  TiX,TiY,TiZ  Tilt on x axis, y axis, z axis
  TiS           Scaling of field of view in the tilt transformation

  TrX,TrY,TrZ  Translation on x axis, y axis, z axis

  Tpy,Tpp      yaw and pitch of remapping plane for translation

  Te0,Te1,Te2,Te3  Test parameters

  Vm           vignetting correction mode (default 0):
                   0: no vignetting correction
                   1: radial vignetting correction (see j,k,l,o options)
                   2: flatfield vignetting correction (see p option)
                   4: proportional correction: i_new = i / corr.
                        This mode is recommended for use with linear data.
                        If the input data is gamma corrected, try adding g2.2
                        to the m line.

                       default is additive correction: i_new = i + corr

                     Both radial and flatfield correction can be combined with the
                      proportional correction by adding 4.
                  Examples: i1 - radial polynomial correction by addition.
                                  The coefficients j,k,l,o must be specified.
                            i5 - radial polynomial correction by division.
                                  The coefficients j,k,l,o must be specified.
                            i6 - flatfield correction by division.
                                  The flatfield image should be specified with the p option

  Va,Vb,Vc,Vd  vignetting correction coefficients. (defaults: 0,0,0,0)
                ( 0, 2, 4, 6 order polynomial coefficients):
                 corr = ( i + j*r^2 + k*r^4 + l*r^6), where r is the distance from the image center
               The corrected pixel value is calculated with: i_new = i_old + corr
               if additive correction is used (default)
                           for proportional correction (h5): i_new = i_old / corr;

  Vx,Vy        radial vignetting correction offset in pixels (defaults q0 w0, optional).
                  Used to correct for offset from center of image
                   Vx - horizontal offset
                   Vy - vertical offset

  S100,600,100,800   Selection(l,r,t,b), Only pixels inside the rectangle will be used for conversion.
                        Original image size is used for all image parameters
                        (e.g. field-of-view) refer to the original image.
                        Selection can be outside image dimension.
                        The selection will be circular for circular fisheye images, and
                        rectangular for all other projection formats

  nName        file name of the input image.

  i f2 r0   p0    y0     v183    a0 b-0.1 c0  S100,600,100,800 n"photo1.jpg"
  i f2 r0   p0    y180   v183    a0 b-0.1 c0  S100,600,100,800 n"photo1.jpg"

Rotate transform the image, angles in degrees:

  $i->Transform ($roll, $pitch, $yaw);

Each image attribute (v, a, b, c etc...) can be read like so:

 $fov = $i->v;

Note that this will return either the value (56.7) or a reference to another image (=0). If you supply a Panotools::Script object as a parameter then the reference will be resolved and you will always get the value:

 $fov = $i->v ($pto);

Get the absolute path to the image file

$i->Path ('/path/to/project.pto');

If a .pto project isn't specified then paths are assumed to be relatve to cwd

For any given coordinate in this image (top left is 0,0), calculate an x,y,z cartesian coordinate, accounting for lens distortion, projection and rotation.

  $coor = $i->To_Cartesian ($pto, [23,45]);
  ($x, $y, $z) = @{$coor};

Query distance (radius) to photo in pixels:

  $pix_radius = $i->Radius ($pto);